COOLRITE SUPER
Is a superior soluble oil which gives a mikly/ translucent emulsion and suitable for cutting of steels, non-ferrous metals and cast iron, cold rolling of steel.

COOLRITE CLEAR
Is a high grade soluble oil which gives a clear emulsion specially suitable for grinding of steel, cast iron and non-ferrous metals. Also hot rolling of aluminium.

COOLRITE HD
Is an extreme pressure soluble oil suitable for severe jobs on large roughing and multitool lathes, for cast iron, steel and non-ferrous metals.

COOLRITE EP
Is a soluble oil formulated for extreme pressure Heavy Duty soluble oil suitable for machining most difficult operations. Can replace neat oils at high conentrations for general machining, multitool and auto lathe drilling broaching and high speed grinding.

SYNCOOL 110
synthetic cutting fluid forming translucent emulsion which contains effective rust preventive additives and other performance additives suitable for high speed machining and grinding jobs. Its emulsion has high bacterial resistance and antifoaming characteristics. SYNCOOL 11 is recommended at 1:50 , 1:30 dilution ratios with water.

SYNCOOL 120
Does not contain oil and forms true transparent solution when mixed with water. The COOLANT solution is exceptionally resistant to bacterial attack providing long coolant life and rust protection to machined parts. SYNCOOL 12 is exceptionally suitable for grinding, maintaining grinding wheels, free cutting edge, without loading.

SYNCOOL 130
Is a semi-synthetic coolant concentrate. It forms a translucent emulsion with water containing selected anti-rust, antibacterial additive with inherent antifoam characteristics. The resultant coolant has long emulsion life in use. The emulsion besides being a keen grinding coolant has a degree of lubricity to provide fine finish. It is recommended for medium high speed to high speed machining on automatics as well as grinding operations.

SARBI’s CUTFINE series can be classified under three main categories :-
1. High oiliness type.
2. EP oils non-staining type.
3. EP oils staining type.

The above oils differ in type and quality of the additives whether non-staining or staining type depending on the point of application, severity and type of the cutting job under taken.

CUTFINE 110, 120 & 130
They are light coloured low viscosity oils, recommended for use in machining all non-ferrous metals (except titanium) and for low tensile steels. This product has good heat transfer properties to cool effectively under high-speed conditions. Contains oiliness & EP additives ideally suited for severe Honing operations.

CUTFINE 150, 240, 270, 275
These oils are amber to red coloured products containing inactive sulphur with or without chlorinated EP additive besides oiliness additives. These products are used in automobile, bearing and ancillary, repetitive metal parts manufacturing industries, such as turning, milling, drilling on automatics as well as honing, lapping and super finishing operations of ferrous and non-ferrous metals. Viscosity of these grades increase as the suffix number increases.

CUTFINE 360, 390, 480
These oils are amber to red coloured products containing active sulphur with or without chlorinated EP additive besides oiliness additives. These products are used in automobile, bearing and ancillary, repetitive metal parts manufacturing industries.

This products are used in machining of high tensile steels, and alloy steels are not recommended for non ferrous metals specially, Bronze, Copper, Brass and Gun Metal.

HONISH 9 & 10
These oils are special honing oils manufactured from highly refined low viscosity base stock with suitable additives specially for Honing operations, giving good cooling and excellent surface finish giving extended tool life. They are also suitable for machining nonferrous metals except Titanium where low viscosity non-staining oil is required. Honish 9 is more compounded.

STEEL ROLLING OIL EP
This is a premium quality oil in water type emulsifiable fluid used in cold rolling of mild steels and medium carbon steels. It forms a stable emulsion with water and has excellent cooling and friction reducing properties which gives increased roll life and reduced power consumption.

STEEL ROLLING OIL HD 9
It is a superior quality neat rolling oil manufactured from highly refined low sulphur base stocks and with anti-wear, anti-oxident and lubricity improver additives. This is non-staining. It can be used in all type of mills including Sendzimir and Seundwig mills.

SARBI STEEL ROLLING OIL 22
It is a superior quality mineral oil with selected anti-oxidant, anti-wear, anti-rust additives. It can be used for cold rolling of alloy steels, nickel and chromium steels and stainless steels. It has excellent cooling and friction reducing ability, achieves better surface finish, and reduces power consumption with increased production.

SARBI STEEL ROLLING COMPOUND EP-2
It is a soft paste based on fatty substances with anti-wear and anti-oxidant additives. It is mixed in suitable proportion with water and is used for cold rolling of steel plates. Normally applied through spray nozzles.

WAY OILS 32, 68, 220, H-32, H-57, H-68

These oils have mild EP, tackiness, anti-rust and anti-foam additives, minimum stick-slip and chatter. These oils are recommended for slide way lubrication of planers, grinders, boring machines, shapers etc.

Way oils H-32, H-57 and H-68 are combined hydraulic and machine tool way lubricants. These have all the properties of the above oils and at the same time serve as hydraulic media in non-critical systems.

KWENCHOL 2 is a selected straight mineral, general purpose quenching oil. Particularly suitable for quenching of steel parts heated in cynide baths.

KWENCHOL 3 is a blend of refined mineral base oils and fatty compounding, lending it good wetting properties with higher quenching speeds than achieved with

KWENCHOL 9 is a mar-quench oil suitable for maintaining bath at 150 - 220 C. It gives predictable quench performance and low reject rates.

PROTEC DW 201, 202, 204 are solvent deposited, water displacing type soft film rust preventives with finger print neutralising properties.

PROTEC DW 201 is solvent deposited water displacing soft film type rust preventive and on the evaporation of solvent forms a thicker and firmer oily film which offers protection to the steel parts for several weeks. It is also best applied by dipping of the machined parts in the oil bath.

PROTEC DW 244 is solvent deposited soft film, water displacing type with finger print neutralising properties. PROTEC DW 244 has been formulated from highly refined lubricating base stocks containing special rust and corrosion protection additives keeping in mind specially the Ball and Roller Bearing rust preventive requirements. It is suitable for surface protection of all highly polished surfaces and as a sealant for phosphatised components. It is also suitable for small parts like taps, dies, screws, nuts and bolts. PROTEC DW 244 is applied by cold dipping or spraying copiously the ball and roller bearings or the parts to be protected. After draining the excess fluid, and on drying of solvent, PROTEC DW 244 leaves a firm oily colourless film. It is desirable to give the solvent drying time of minimum 12 hrs. but preferably 24 hrs. for good results.

PROTEC 611 & 612 are made from specially selected lubricating base oils containing special rust and corrosion inhibitors. They offer high degree of protection to steel and other polished metallic surfaces from rust and corrosion. They also posses lubricating property besides being temporary corrosion protective.

PROTEC DW 717 is a solvent deposited, water displacing type rust preventive which forms soft waxy brown film on the metal surface and is designed to stand a degree of handling of the protected surfaces. PROTEC DW 717 is popularly used as temporary protective for steel tubes, bright bars, steel strips, wheel rings, auto parts, etc. Application is by brushing, dipping, spraying or roller coating.

TERIC - Rust and Oxidation inhibited Grades
TERIC – AW - Antiwear type grades
TERIC CR

Designed to provide excellent lubrication for long period at high temperatures for reciprocating and rotary air compressors.

TERIC CRM
Contains special additives to meet critical requirements of ammonia compressors. These oils have high thermal oxidation and chemical stability as well as good demulsibility properties.

DELTA GEAR OILS for Industrial applications are formulated from refined base lubricating oils and selected additives in various viscosity grades to meet numerous industrial gear lubrication needs. They are available in two types.

DELTA EP based on sulphur phosphorus type EP additives.
Grades : EP 68, EP 100, EP 150, EP 220, EP 320, EP 460,EP 680

DELTA LS based on sulphur-lead based EP additives.
Grades : EP 68, EP 100, EP 150, EP 220, EP 320, EP 460, EP 680

HEATOL 32/100
Heatol 32 and 100 are hydrocarbon type heat transfer medium used in Thermic Boilers. They are based on specially selected and highly refined base oils fortified with additives. They have excellent Thermal stability, Oxidation stability and low evaporation at elevated temperature offering good pumpability essential for long life of thermic heating system. Heatol 100 is useful where the Thermic fluid system has to operate continuously at high temperatures 260 / 300 C.

SPINOL - 2, 5, 12, 22
Spinols are blended from highly refined low viscosity base stocks having inherent oxidation and chemical stability. They are further fortified with anti-oxidant, anti-wear, anti-rust and defoamant additives. They are recommended for bearing lubrication of high-speed textile spindles and machine tool spindles. They can also be used in timing gears, blowers and servomechanism and some hydraulic systems of precision machine tools.

INVERT EMULSIONS TYPE :
TERIC WO 46, 68, 100
These are invert oil in water type fire resistant hydraulic fluids used in hydraulically operated mining pit-props. These form stable emulsion with water and give long satisfactory service life in hydraulic systems, which operate under condition of fire hazard but system temperatures of 70°C max. These meet IS 10532 (Part I) - 1983 HF - A grade I and HF - A grade II specifications.

WATER GLYCOL TYPE :
TERIC WG 22, 46, 68These are water glycol based fire resistant hydraulic fluids. These are solutions containing glycols and water.

PHOSPHATE ESTERS TYPE :
TERIC PE 32 & 68
These fluids are specially formulated from selected phosphate esters, which have inherent fire resistance. They are specially suitable when operational temperature constraint of invert emulsion and water glycol type grades is a problem. Maximum temperature of operation 120°C.

MACHOL range of lubricating oils is formulated from refined base stocks and possess good inherent thermal oxidation and chemical stability as well as lubrication properties. They are non corrosive neutral fluids of different viscosity’s to suit variety of applications

Grades : 32, 68, 100, 150, 220, 320, 460